The "WizardProg Mobile" (professional version application is "WizardProg Expert") application software designed to manage the programming operation for the universal portable USB-programmer TL866A/CS and other programmer models which fully compatible with it. This system is used to program a wide range of E(E)PROM chips, microcontrollers internal EEPROM, testing SRAM chips and logic chips.
The application allows you to achieve a new level of mobility and efficiency when using the programmer TL866, which is used widely to repair and adjustment:
· automotive computers, computer-unit and radio;
· personal computers;
· any other modern electronic equipment.
The "WizardProg Mobile" system is used by service technicians of electronics, amateur radio operators and developers of modern electronic devices for the purpose of:
· repair and restore the microelectronic device and firmware;
· promptly update the firmware of microelectronic devices;
· assist in the embedded electronics construction and setting up the microcontroller units;
· replicate numerous useful designs using advanced electronic components.
Main characteristics and features of the "WizardProg Mobile" microelectronic programming system are:
· Fast and reliable programming, in most cases with significantly better speed than the similar systems.
· The programmer's low power consumption when powered by USB (OTG)-cable from the mobile device battery.
· Support for a wide range of integrated circuits (ICs): the memory of a large capacity up to 128Mbit (EPROM, FLASH, EEPROM I2C/3-wire/SPI), microcontrollers PIC, Atmel-AVR, MCS-51 based SST, SyncMOS, Winbond. PLD chips, GAL.
TL866 programmer does not need an external power supply and it operates using the power sources of a tablet or mobile phone which is connected to via USB interface. Physical linking to a mobile device is provided with a USB cable fully supporting OTG (On-The-Go) protocol.
Important note! The target control tablet or mobile phone must have a fully implemented hardware support of OTG access too!
Currently "WizardProg Mobile" mobile application is completely autonomous in operation, does not need a permanent connection to the Internet, allowing you to use it even without access to communication networks.
Both of programmer's models TL866CS and TL866A(ICSP) are fully supported. The modern version of the TL866II Plus programmer currently is not supported by the "WizardProg Mobile" system!
Device list for the current application version: http://www.wizardprog.com/wp/dblist/recent_version_chiplist.htm
Phần mềm ứng dụng "WizardProg Mobile" (ứng dụng phiên bản chuyên nghiệp là "WizardProg Expert") được thiết kế để quản lý hoạt động lập trình cho trình lập trình USB di động phổ biến TL866A / CS và các mô hình lập trình viên khác hoàn toàn tương thích với nó. Hệ thống này được sử dụng để lập trình một loạt các chip E (E) PROM, EEPROM bên trong vi điều khiển, thử nghiệm chip SRAM và chip logic.
Ứng dụng cho phép bạn đạt được một mức độ di động và hiệu quả mới khi sử dụng lập trình viên TL866, được sử dụng rộng rãi để sửa chữa và điều chỉnh:
· Máy tính ô tô, máy tính đơn vị và đài phát thanh;
· những máy tính cá nhân;
· Bất kỳ thiết bị điện tử hiện đại khác.
Hệ thống "WizardProg Mobile" được sử dụng bởi các kỹ thuật viên dịch vụ điện tử, nhà điều hành vô tuyến nghiệp dư và nhà phát triển các thiết bị điện tử hiện đại cho mục đích:
· Sửa chữa và khôi phục thiết bị và chương trình cơ sở vi điện tử;
· Cập nhật kịp thời phần sụn của các thiết bị vi điện tử;
· Hỗ trợ xây dựng thiết bị điện tử nhúng và thiết lập các bộ vi điều khiển;
· Nhân rộng nhiều thiết kế hữu ích bằng cách sử dụng các linh kiện điện tử tiên tiến.
Các đặc điểm và tính năng chính của hệ thống lập trình vi điện tử "WizardProg Mobile" là:
· Lập trình nhanh và đáng tin cậy, trong hầu hết các trường hợp với tốc độ tốt hơn đáng kể so với các hệ thống tương tự.
· Mức tiêu thụ năng lượng thấp của lập trình viên khi được cung cấp bởi USB (OTG) từ pin thiết bị di động.
· Hỗ trợ cho một loạt các mạch tích hợp (IC): bộ nhớ có dung lượng lớn lên tới 128Mbit (EPROM, FLASH, EEPROM I2C / 3-dây / SPI), vi điều khiển PIC, Atmel-AVR, SST dựa trên MCS-51, SyncMOS, Winbond. Chip PLD, GAL.
Lập trình viên TL866 không cần nguồn điện bên ngoài và nó hoạt động bằng cách sử dụng các nguồn năng lượng của máy tính bảng hoặc điện thoại di động được kết nối qua giao diện USB. Liên kết vật lý với thiết bị di động được cung cấp với cáp USB hỗ trợ đầy đủ giao thức OTG (On-The-Go).
Lưu ý quan trọng! Máy tính bảng điều khiển mục tiêu hoặc điện thoại di động cũng phải có hỗ trợ phần cứng được triển khai đầy đủ khi truy cập OTG!
Hiện tại ứng dụng di động "WizardProg Mobile" hoàn toàn tự động hoạt động, không cần kết nối Internet vĩnh viễn, cho phép bạn sử dụng ngay cả khi không truy cập vào mạng truyền thông.
Cả hai mô hình lập trình viên TL866CS và TL866A (ICSP) đều được hỗ trợ đầy đủ. Phiên bản hiện đại của lập trình viên TL866II Plus hiện không được hỗ trợ bởi hệ thống "WizardProg Mobile"!
Danh sách thiết bị cho phiên bản ứng dụng hiện tại: http://www.wizardprog.com/wp/dblist/recent_version_chiplist.htmlm